Digi Config
m |
m |
||
| Line 8: | Line 8: | ||
The relevant serial commands are: | The relevant serial commands are: | ||
| − | ALIAS <n> <callsign> | + | '''ALIAS''' <n> <callsign> |
Sets digipeater alias for slot <n>, where n is between 1 and 8. This will | Sets digipeater alias for slot <n>, where n is between 1 and 8. This will | ||
typically be a generic alias like ʹWIDEʹ. No SSID is allowed in this field. | typically be a generic alias like ʹWIDEʹ. No SSID is allowed in this field. | ||
| − | DIGI on|off | + | '''DIGI''' on|off |
When enabled, the tracker will digipeat packets having its own callsign | When enabled, the tracker will digipeat packets having its own callsign | ||
(MYCALL) in the next digipeater address field. | (MYCALL) in the next digipeater address field. | ||
| − | DIGIID <n> on|off | + | '''DIGIID''' <n> on|off |
Enables callsign substitution for digipeater alias <n> (1 to 8). This should | Enables callsign substitution for digipeater alias <n> (1 to 8). This should | ||
normally be enabled. | normally be enabled. | ||
| − | DUPETIME <0‐255> (seconds) | + | '''DUPETIME''' <0‐255> (seconds) |
Sets digipeating duplicate suppression period. | Sets digipeating duplicate suppression period. | ||
| − | HOPLIMIT <n> <hops> | + | '''HOPLIMIT''' <n> <hops> |
For digipeater alias <n> (1‐8), sets the maximum number of digipeater | For digipeater alias <n> (1‐8), sets the maximum number of digipeater | ||
hops allowed. This can be used to limit excessively long paths that may | hops allowed. This can be used to limit excessively long paths that may | ||
cause network degradation. | cause network degradation. | ||
| − | PREEMPT <n> on|off | + | '''PREEMPT''' <n> on|off |
Enables digipeater preemption for alias <n> (1‐8). If preemption is | Enables digipeater preemption for alias <n> (1‐8). If preemption is | ||
enabled, packets will be digipeated on this alias even if it isnʹt the next | enabled, packets will be digipeated on this alias even if it isnʹt the next | ||
address in the packet’s digipeater list. | address in the packet’s digipeater list. | ||
| − | USEALIAS <n> on|off | + | '''USEALIAS''' <n> on|off |
Enables digipeating for alias n. | Enables digipeating for alias n. | ||
Revision as of 14:58, 9 October 2008
Back to manual[[1]]
Configuring the Digipeater Settings
The relevant serial commands are:
ALIAS <n> <callsign> Sets digipeater alias for slot <n>, where n is between 1 and 8. This will typically be a generic alias like ʹWIDEʹ. No SSID is allowed in this field.
DIGI on|off When enabled, the tracker will digipeat packets having its own callsign (MYCALL) in the next digipeater address field.
DIGIID <n> on|off Enables callsign substitution for digipeater alias <n> (1 to 8). This should normally be enabled.
DUPETIME <0‐255> (seconds) Sets digipeating duplicate suppression period.
HOPLIMIT <n> <hops> For digipeater alias <n> (1‐8), sets the maximum number of digipeater hops allowed. This can be used to limit excessively long paths that may cause network degradation.
PREEMPT <n> on|off Enables digipeater preemption for alias <n> (1‐8). If preemption is enabled, packets will be digipeated on this alias even if it isnʹt the next address in the packet’s digipeater list.
USEALIAS <n> on|off Enables digipeating for alias n.
