Digi Config - Revision history

UR3IRS at 18:22, 2 February 2009

2009-02-02T18:22:54Z

Anonymous at 02:55, 10 October 2008

2008-10-10T02:55:31Z

Anonymous at 21:58, 9 October 2008

2008-10-09T21:58:15Z

Anonymous at 21:57, 9 October 2008

2008-10-09T21:57:15Z

Anonymous: /* Digi Config */

2008-09-27T21:02:11Z

‎Digi Config

Anonymous: New page: == Digi Config == Back to manualhttp://info.aprs.net/index.php?title=Otwincfg.exe '''Configuring the Digipeater Settings''' [[Image:DigiSettings.j...

2008-09-27T20:38:55Z

New page: == Digi Config == Back to manualhttp://info.aprs.net/index.php?title=Otwincfg.exe '''Configuring the Digipeater Settings''' [[Image:DigiSettings.j...

New page

== Digi Config ==
Back to manual[[http://info.aprs.net/index.php?title=Otwincfg.exe]]

'''Configuring the Digipeater Settings'''

[[Image:DigiSettings.jpg]]

@@ Line 10: / Line 10: @@
 '''ALIAS''' <n> <callsign>
 Sets digipeater alias for slot <n>, where n is between 1 and 8. This will
 typically be a generic alias like ʹWIDEʹ. No SSID is allowed in this field.
 '''DIGI''' on|off
@@ Line 26: / Line 27: @@
 For digipeater alias <n> (1‐8), sets the maximum number of digipeater
 hops allowed. This can be used to limit excessively long paths that may
-cause network degradation.
+cause network degradation.  Thus if alias 1 is WIDE then HOPLIMIT 1 2 will
 '''PREEMPT''' <n> on|off

@@ Line 8: / Line 8: @@
 The relevant serial commands are:
-ALIAS <n> <callsign>
+'''ALIAS''' <n> <callsign>
 Sets digipeater alias for slot <n>, where n is between 1 and 8. This will
 typically be a generic alias like ʹWIDEʹ. No SSID is allowed in this field.
-DIGI on|off
+'''DIGI''' on|off
 When enabled, the tracker will digipeat packets having its own callsign
 (MYCALL) in the next digipeater address field.
-DIGIID <n> on|off
+'''DIGIID''' <n> on|off
 Enables callsign substitution for digipeater alias <n> (1 to 8). This should
 normally be enabled.
-DUPETIME <0‐255> (seconds)
+'''DUPETIME''' <0‐255> (seconds)
 Sets digipeating duplicate suppression period.
-HOPLIMIT <n> <hops>
+'''HOPLIMIT''' <n> <hops>
 For digipeater alias <n> (1‐8), sets the maximum number of digipeater
 hops allowed. This can be used to limit excessively long paths that may
 cause network degradation.
-PREEMPT <n> on|off
+'''PREEMPT''' <n> on|off
 Enables digipeater preemption for alias <n> (1‐8). If preemption is
 enabled, packets will be digipeated on this alias even if it isnʹt the next
 address in the packet’s digipeater list.
-USEALIAS <n> on|off
+'''USEALIAS''' <n> on|off
 Enables digipeating for alias n.

← Older revision		Revision as of 21:57, 9 October 2008
Line 5:		Line 5:

	[[Image:DigiSettings.jpg]]		[[Image:DigiSettings.jpg]]
		+
		+	The relevant serial commands are:
		+
		+	ALIAS <n> <callsign>
		+	Sets digipeater alias for slot <n>, where n is between 1 and 8. This will
		+	typically be a generic alias like ʹWIDEʹ. No SSID is allowed in this field.
		+
		+	DIGI on\|off
		+	When enabled, the tracker will digipeat packets having its own callsign
		+	(MYCALL) in the next digipeater address field.
		+
		+	DIGIID <n> on\|off
		+	Enables callsign substitution for digipeater alias <n> (1 to 8). This should
		+	normally be enabled.
		+
		+	DUPETIME <0‐255> (seconds)
		+	Sets digipeating duplicate suppression period.
		+
		+	HOPLIMIT <n> <hops>
		+	For digipeater alias <n> (1‐8), sets the maximum number of digipeater
		+	hops allowed. This can be used to limit excessively long paths that may
		+	cause network degradation.
		+
		+	PREEMPT <n> on\|off
		+	Enables digipeater preemption for alias <n> (1‐8). If preemption is
		+	enabled, packets will be digipeated on this alias even if it isnʹt the next
		+	address in the packet’s digipeater list.
		+
		+	USEALIAS <n> on\|off
		+	Enables digipeating for alias n.

@@ Line 1: / Line 1: @@
-Back to manual[[http://info.aprs.net/index.php?title=Otwincfg.exe]]
+[[Otwincfg.exe|Back to manual]]
-−
-'''Configuring the Digipeater Settings'''
-−
 [[Image:DigiSettings.jpg]]